To Non-Java ALLSTAR Network Website

                                                                                                                                                                        JAVA-capable browser required for graphic-based menus (Exploer 3.0 or Netscape 2.0 or greater)

Please let me remind all of you--this material is copyrighted.  Though partially funded by NASA, it is still a private site.  Therefore, before using our materials in any form, electronic or otherwise, you need to ask permission.
There are two ways to browse the site: (1) use the search button above to find specific materials using keywords; or,
(2) go to specific headings like history, principles or careers at specific levels above and click on the button.
Teachers may go directly to the Teachers' Guide from the For Teachers button above or site browse as in (1) and (2).

FAQnewred.gif (906 bytes)           

Section 1.18 - Types of Actuation Cylinders

hrule_bl.gif (260 bytes)

Introduction

The function of the actuating cylinder is to take the pressure and hydraulic fluid flow and change them into either linear or rotary motion. The ones that have been employed more commonly are the double action actuating cylinders, because they work in both directions.

Group I

A. Single Piston, Single Rod

This type of actuating cylinder has one piston connected to one rod. Such a device requires the piston rod to move into the actuating cylinder to cause one motion to occur and to move out of the cylinder to cause the reverse motion to occur.

hydro060a.gif (1600 bytes)

B. Single Piston, Double Rod

This is an equal displacement cylinder and could be used on an aileron system or an automatic guidance system (as shown in the second diagram below).

hydro060.gif (1955 bytes)

The piston ends can be attached to a pulley system that can pivot a control surface.  The motion of the piston to the right, due to high pressure fluid in the left side of the actuating cylinder, can be activate the pulley system and pivot the control surface upward.  By reversing the flow, the opposite motion will occur.

hydro061.gif (2018 bytes)

C. Double Piston, Double Rod

 This type of actuating cylinder would be used on bomb bay doors (figure shown below right). High pressure fluid enters the center section of the cylinder, acting on the two pistons simultaneously. The rods would be extended outward, causing the doors to rotate open. When the high pressure fluid enters the two end sections (shown in blue), this operation is reversed, closing the bomb bay doors.

hydro062.gif (2014 bytes) hydro063.gif (971 bytes)

Another application for the Double Piston, Double Rod cylinder is the brake system of a vehicle. Click here to see.

Group II

A. Single Action Cylinders

Bungee Type- this type of actuating cylinder is used where gravity or weight can act as high pressure oil. Either a rubber mass or a spring loading device counteracts the weight. Its disadvantages include:

  1. The decrease in piston stroke on account of weight and size of spring or inserted rubber mass;
  2. The fact that oil on the spring side of the piston must move both the piston and the spring;
  3. The size and weight of the spring to do the job might be too great.

hydro064.gif (1545 bytes) hydro065.gif (805 bytes)

B. Dashpot Cylinder

A dashpot cylinder is any cylinder which decelerates piston movement at the end of the stroke. The piston has a small attachment at the piston head side that fits into a dashpot (A).  When the piston moves to the left in the diagram below, by forcing the fluid out of the dashpot (A), energy is taken out of the system, causing the piston to slow down.

hydro066.gif (1317 bytes)

C. Locking Cylinder

The locking cylinder is a cylinder which has a locking device attached to it. This cylinder is a "fail-safe" design so that it will not actuate beyond some given point.

hydro067.gif (2483 bytes)

D. Telescoping Cylinder

The telescoping cylinder is a cylinder-piston configuration within a cylinder-piston configuration which is used to get a larger stroke from a small cylinder.  This may be required when the cylinder must fit into a small space but the piston     rod must move through a large distance.

hydro068.gif (1638 bytes)

Group III

A. Stationary Piston-Moveable Cylinder

Whenever we don’t want the piston rod to extend into an environment that can damage the rod or contaminate the hydraulic fluid (for example, a stream of sea spray or in the path of little pebbles when landing or taking off from a      rough airstrip), we make the piston cylinder extend instead of the piston rod. The type of cylinder we use is the   stationary piston moveable cylinder.

hydro069.gif (2202 bytes)               hydro070.gif (2892 bytes)

B. Rotary Motion Actuating Cylinder

hydro071.gif (2179 bytes)


In this type of cylinder, as the piston moves backwards and forwards, it rotates the rotating cam (circular cam in the center of the diagram).  The cam is connected to a shaft which rotates as well, thus converting the linear motion of the piston into the rotary motion of the cam and the shaft.

hydro072.gif (1864 bytes)
Vacuum rotary windshield wiper

An example of the rotary motion actuating cylinder can be found in certain windshield wiper systems (above).  In these windshield wipers systems, as the wiper makes the last part of its stroke, it is designed to trip a selector valve (SV) connection, reversing the air-vacuum flow so that the wiper will reverse direction.

hydro073.gif (1546 bytes)


In the double cylinder system shown above, both pistons move in tandem to rotate the gear shown in the center of the diagram.  That gear may be connected to a shaft that rotates.  Thus, we have converted the linear motion of the piston rods into a rotary motion of the gear.


Send all comments to allstar@fiu.edu
1995-2017 ALLSTAR Network. All rights reserved worldwide.

Funded in part by

Updated: March 12, 2004