To Non-Java ALLSTAR Network Website

                                                                                                                                                                        JAVA-capable browser required for graphic-based menus (Exploer 3.0 or Netscape 2.0 or greater)

Please let me remind all of you--this material is copyrighted.  Though partially funded by NASA, it is still a private site.  Therefore, before using our materials in any form, electronic or otherwise, you need to ask permission.
There are two ways to browse the site: (1) use the search button above to find specific materials using keywords; or,
(2) go to specific headings like history, principles or careers at specific levels above and click on the button.
Teachers may go directly to the Teachers' Guide from the For Teachers button above or site browse as in (1) and (2).

FAQnewred.gif (906 bytes)           

Section 1.22 - Pressure Boosters,

Pressure De-Boosters, & Hydraulic Fluids

hrule_bl.gif (260 bytes)

Pressure Boosters

Pressure boosters are rarely used in aircraft (almost all planes use de-boosters). If we need higher pressure, we must change the ENTIRE power and actuating system. This adds weight that is not needed. In general, we cannot put in larger pistons and piston cylinders to increase the power, because, normally, we don’t have the room for it. A simple solution is to raise the pressure in a LOCALIZED area.

The function of a pressure booster is to act like a transformer--that is, it raises the pressure of a small circuit connected to the power system. The booster is a cylinder made up of two pistons of different surface areas that are connected. The larger surface area (A1) is connected to the inlet side of the hydraulic system, and, the smaller surface area (A2) is connected to the outlet side of the hydraulic system

hydro085.gif (1723 bytes)

hydro086.gif (2148 bytes)

Example:
Suppose that the actuating cylinder (used to move the control surface) normally gets hydraulic fluid at a pressure of
p = 1000 psi and that this pressure would act on a piston surface area A = 10 square inches. The total force developed F would be p times A or 10,000 lb. But, suppose we need a force of 60,000 lb to move the control surface... So we add a booster.

If the inlet side area A1 is 3 square inches, then the force, F, developed by the hydraulic fluid is

Eq036.gif (487 bytes)

Since the pistons of the booster are connected, and we assume that they have negligible inertia, then the force developed on the smaller piston is the same as the force on the larger piston. If the outlet side area A2 is 1/2 square inch, then the pressure developed on the outlet side would be

Eq034.gif (657 bytes)

At the actuating cylinder the force developed would be the pressure times the area of the actuating cylinder or

(6000 lb/sq. in.) x (10 sq. in.) = 60,000 lb

as required.

Disadvantages of a Pressure Booster 

If a 3 inch piston stroke is needed from the actuating cylinder moving the control surface, then the total volume of fluid moved by the actuating piston's movement is stroke x piston area = (3 inches) x (10 square inches) = 30 cubic inches

This is the volume of fluid that must move out of the booster to the actuating cylinder. Thus the smaller piston in the booster must stroke a distance equal to the volume of fluid needed divided by the piston area = (30 cu. in.) / (1/2 sq. in.) = 60 inches = 5 feet!

 

Pressure De-Boosters

Pressure deboosters are used to reduce the pressure in the system to a level that can be used by certain devices. Pressure deboosters are pressure boosters turned upside down (that is, the inlet side of the booster has the smaller area piston and the outlet side has the larger area piston). They are employed in power brake systems, using engine power to help apply the brakes. Since aircraft wheels are made of magnesium, any high pressure on the wheels will cause them to split. That is why they must de-boost the pressure gotten from engine.

The inlet line to the debooster comes from the power brake control valve. The outlet line goes to the brake system.  This valve meters hydraulic fluid and hydraulic pressure directly. The force applied to the wheels to make them stop is proportional to how hard you push on the rudder pedal. It is normally used for a 1 or 2 cubic inch application.

hydro088.gif (2358 bytes)                          hydro087.gif (2013 bytes)

Hydraulic Fluids

Hydraulic fluids that have been used are of several types: water-based, mineral-based and synthetic type oils. Each has its advantages and disadvantages. Though several types are listed here, newer types of oils are being developed.

  1. Water-based MIL-O-7083 type hydraulic fluid has been used in naval aircraft because it is not flammable. However, it is still corrosive. It is a water based lubricant which is chemically treated. Its commerical name is HYDROLUBE
  2. Mineral-based petroleum oil MIL-O-5606 has been used by NATO. Old name of this type fluid is AN-VV-O-366. It has a cherry red dye added to it.
    One caveat needs to be stated here: You are not allowed to mix oil bases since the usefulness and range of use of the oil may be degraded.
  3. Synthetic Oils have much appeal. They are non-flammable and work over a wide temperature range. One such synthetic oil is known as Skydroll 500 and it has a purple or green color. It is made from a phosphate-ester base.

Caution: Never use a vegetable-base oil. At high temperatures, vegetable-based oils form a residue which is gummy and can clog the hydraulic system, which can lead to catastrophic results.

 


Send all comments to allstar@fiu.edu
1995-2017 ALLSTAR Network. All rights reserved worldwide.

Funded in part by

Updated: March 12, 2004